What is the details for Meter For Remote read Model 15-25 water meter?
Product Description--Water meter remote reading type
--Magnetic drive, protected against external magnetic tampering;
--Vacuum sealed register, frost resistant, keeps clear reading for long time;
--Brass body can be painted
--External adjusting device,;
--For cold water;
--Remote transmission device can be added upon request
--Many kinds of sensors, such as Reed Switch, Hall and Weagand can be supplied upon request Pulse output may be 1l/pulse ,10l/pulse ;
--The meters conform to ISO4064 Standard Class B
2. Working condition:
--Water pressure≤1MPa (PN: 1.6MPa/16bar)
From minimum flow-rate (qmin) inclusive, to transitional flow-rate (qt), exclusive:±5%
From transitional flow-rate (qt) inclusive, to overload flow-rate (qs), exclusive:±2%
|flow ratio||Q3/Q1||80 ~ 100|
|overload flow Q 4||M3/h||3.125||5||7.875|
|permanent flow Q 3||M3/h||2.5||4||6.3|
|transitional flow Q 2||M3/h||0.04||0.064||0.126|
|Min flowQ 1||M3/h||0.025||0.05||0.063|
|readings||M3||0.0001 -- 9999|
4. Installation And Usage for the Remote Reading Water Meter
Select the right water meter according to nominal flow rate which is less than or next to the rate through the pipe. It is not a good way for the user to buy the water meter based on the pipe size.
The place to be installed should be free from sunshine, frost, pollutant and water. During the period of frost, the inlet valve in the meter should be closed and the outlet valve and water tap should be open except for being packed for thermal insulation, thus to prevent the damage from being frozen.
Meter should be installed horizontally, and the digits on the dial is up to the face and arrow direction in the meter should be same with the flow.
The stone, sand and slight impurities in the new installed pipe should be cleared off for the sake of the meter fault.
For the purpose of metering accurately, the water tap should be higher than the meter.
Water meter should be not connected with pipe and there are live interface (e.g. pipe interface, connection screw, sealing washer etc.) between the meter and pipe. The meter should not be damaged due to the over-stress caused by pipe and its elements during installation.
1. Materials: brass body, ABS inner core, brass sealing ring, pulse output wire
2. Working Condition: Temperature ≤50°C
3. Measured by Cubic Meter
4. Quantity of Flow:
Q3/Q1=100 Q2/Q1=1.6 Q4/Q3=1.25
5. Working pressure: 1.0 Mpa
6. Loss of pressure: ≤0.1 Mpa
7. Indicating error:
at low zone of Qmin to Qt (not including) is ±5%
at high zone of Qt to Qmax is ±2%
8. Dimension and Weight for Remote Reading Water Meter
Comparison of 2 type Remote reading water meter
|Pulse Output Water meter||Photoelectric Direct Reading Water Meter|
|Electromagnetic interference||Pulse signal susceptible to external electromagnetic interference during transmission||Materials not magnetic sensor, meter reading data instantly, without outside electromagnetic interference|
|Power||Must maintain uninterrupted power supply, the loss of power will cause the system to data errors||Systems usually do not work, no electricity, no power ,when reading the meter ,the power will supply ,after reading it will stop supply power|
|Meter reverse||when water supply is cut off ,the meter will possible reversal and couse secondary pulse signal, resulting in measurement error||Directly read the pointer value or the figure show on the meter face plate, without water meter reverse impact|
|Demagnetization phenomenon||With the extension of the use of small magnets,it will appear demagnetization ,can not send out the output pulse normally, resulting in an error||Direct-reading meter, the sensor is not magnetic material, there is no demagnetization phenomenon|
|Accuracy||Due to the above reasons, resulting in inconsistencies of the reading data between the meter and the computer shows||Direct-reading meter reading similar way as the human eye, so between the meter shows the number of data and computer keep the same.|
Why you choose us - Gaoxiang Water Meter Co.,LTD ?
We could accept your trial order,then you can take this opportunity to check the quality of our products & service of our company
Buyer's logo imprint accepted
We can supply you sample for checking quality,if you pay for the sample & sample freight. we will deliverto you in 1-3 days after we got your payment.
The normal Lead time is 15-30 days , which depends on your quantity.
L/C, T/T, Western Union, MoneyGram, Paypal.
We can arrange the shipping by Courier ( DHL, UPS, Fedex , TNT etc. ), by air or by sea for you.
Please tell us which shipping way that you want and your detailed address, your nearest airport or seaport.
List Of Competitive Advantage:
We are factory, can provide you high quality, best price
Professional employee and effective management
Professional trading service
Good service & reputation
Large production line
Welcome to visite our factory
Quality Controll ( Testing & Packing & Certificates)
If you are interested in our products ,pls feel free to contact us !
Press this link and reply ^ _ ^